Arcam Diva A70
- CONTINUOUS POWER OUTPUT PER CHANNEL
BOTH CHANNELS DRIVEN 8Ω, 20HZ-20KHZ 50W
SINGLE CHANNEL 4Ω, 1KHZ 100W
DISTORTION 8Ω, 80% POWER, 1KHZ 0.005%
PHONO CARTRIDGE INPUT ( WHERE FITTED) MM
INPUT SENSITIVITY 2.7MV
LINE AND TAPE INPUTS
INPUT SENSITIVITY FOR RATED 8 OHMS POWER OUTPUT 650MV
INPUT IMPEDANCE 22KΩ
SIGNAL TO NOISE RATIO* 98DB
PREAMPLIFIER OUTPUTS
NOMINAL OUTPUT LEVEL 545MV
OUTPUT IMPEDANCE <50Ω
GENERAL
POWER CONSUMPTION (MAXIMUM) 450VA
SIZE W/D/H MM. INC. FEET 430 x 330 x 85
WEIGHT (NET) 7.5KG
Exposure 2010S
| • |
Power Output: 75 Watts per channel RMS 8 ohms |
| • |
Input Sensitivity: 250mV |
| • |
Input Impedance: >14K ohms, line input |
| • |
Pre-amplifier Output: gain + 18dB |
| • |
Frequency Response: 20Hz - 20 KHz ±0.5dB |
| • |
Total Harmonic Distortion: <0.05% at 1KHz, rated power |
| • |
Signal to Noise: >100 dB, A weighted, ref rated output |
| • |
Channel Separation: 20Hz-20KHz, >60dB |
| • |
Mains Supply: 110/120V or 220/240V, 50/60Hz (factory set) |
| • |
Max Power Consumption: 200VA (both channels driven, 8 Ohm load) |
| • |
Dimensions (H x W x D): 90mm x 440mm x 310mm |
| • |
Nett Weight (unpacked): 7.0 kg |
| • |
Gross Weight (packed): 9.0 kg |
Cambridge 340A
| Power Output: |
45 watts (into 8 ohms)
55 watts (into 4 ohms)
|
| Input Impedance: |
40k Ohms
|
| Max. Power Consumption: |
360 watts
|
| Loudspeaker Impedance: |
4 – 8 Ohms
|
| Input Sensitivity: |
Line: 350mV
|
| Tone Controls: |
Bass: +/- 7dB @ 80Hz
Treble: +/- 7dB @ 20Hz
|
| Total Harmonic Distortion: |
1kHz<0.09%
1kHz<0.09%
|
| Frequency Response: |
(-1dB) 5Hz - 50kHz
|
| Signal to Noise Ratio: |
92dB (unweighted)
|
| Slew rate (into 8 ohms): |
20V/uS
|
| Dimensions (H x W x D): |
70 x 430 x 310mm
2.8 x 16.9 x 12.2"
|
| Weight: |
6.2kg
15.4lbs
|
Cambridge 540A
| Power Output: |
60 Watts into 8 Ohms
90 Watts into 4 Ohms
|
| Input Impedance: |
47k Ohms
|
| Loudspeaker Impedance: |
4 to 8 Ohms
|
| Line: |
330mV
|
| Phono (using optional phono stage): |
1.75mV
|
| Total Harmonic Distortion (into 8 Ohms 80% rated power): |
0.002% THD (No weighting) @ 1kHz
0.0015% THD (A weighted) @ 1kHz
0.025% THD 20Hz-20kHz @ 10W
|
| Frequency Response: |
5Hz to 50KHz +/- 1dB
|
| Bass: |
+/- 10dB @ 100Hz
|
| Treble: |
+/- 10dB @ 10kHz
|
| Signal to Noise Ratio (No weighting): |
>85dB
|
| Slew rate (into 8 ohms): |
>30V/uS
|
| Max. Power Consumption: |
515 watts
|
| Dimensions (W x D x H): |
430 x 310 x 100mm
16.9 x 12.2 x 3.9"
|
| Weight: |
7.4 kg
16.3 lbs
|
Cambridge 640A
| Power Output: |
75 watts into 8 Ohms
120 watts into 4 Ohms
|
| Input Impedance: |
47k Ohms
|
| Loudspeaker Impedance: |
4 to 8 Ohms
|
| Line: |
330mV
|
| Phono (using optional phono stage): |
1.75mV
|
| Total Harmonic Distortion (into 8 Ohms 80% rated power): |
0.002% THD (No weighting) @ 1kHz
0.0015% THD (A weighted) @ 1kHz
0.02% THD 20Hz - 20kHz @ 10W
|
| Frequency Response: |
5Hz to 50kHz +/- 1dB
|
| Bass: |
+/- 7.5dB @20Hz
|
| Treble: |
+/- 7.5dB @20kHz
|
| Signal to Noise Ratio (No weighting): |
90dB
|
| Slew rate (into 8 ohms): |
30V/uS
|
| Max. Power Consumption: |
515 Watts
|
| Dimensions (W x D x H): |
430 x 310 x 100mm
16.9 x 12.2 x 3.9"
|
| Weight: |
7 kg/15.4 lbs
|
Cambridge 740A
| Power Output: |
100W RMS into 8 Ohms
150W RMS into 4 Ohms
|
| THD (unweighted): |
< 0.001% 1 kHz at 80% of rated power
< 0.01% 20 Hz - 20 kHz at 80% of rated power
|
| Frequency Response: |
10 Hz - 50 kHz +/- 1 dB
|
| Signal to Noise Ratio: |
>96dB (ref 1W/8 Ohm)
|
| Input Impedance: |
Inputs 1-6 47 kOhm
Tape Input 47 kOhm
|
| Power amp damping factor: |
> 110 at 1 kHz
|
| Max. Power Consumption: |
750W
|
| Min. Power Consumption: |
Active (no signal) 45W
Standby 6W
|
| Bass: |
Shelving type
Max bass boost/cut
+/- 10 dB at 10 Hz
|
| Treble: |
Shelving type
Max treble boost/cut
+/- 7.5 dB at 20 kHz
|
| Dimensions (H x W x D): |
115 x 430 x 350mm
4.5 x 16.9 x 13.8"
|
| Weight: |
10.7kg (23.5Lbs) |
Cambridge 840A
| Power Output: |
120W RMS into 8 Ohms
200W RMS into 4 Ohms
|
| Input Impedance: |
Input 1 (balanced) 20 kOhm
Inputs 2-7 20 kOhm
Tape Input 20 kOhm
|
| THD (unweighted): |
< 0.001% 1 kHz at 80% of rated power
< 0.01% 20 Hz - 20 kHz at 80% of rated power
|
| Frequency Response: |
10 Hz - 50 kHz +/- 1 dB
|
| Signal to Noise Ratio: |
> 93 dB
|
| Power amp damping factor: |
> 110 at 1 kHz
|
| Max. Power Consumption: |
800W
|
| Min. Power Consumption: |
Active (no signal) 70W
Standby 7W
|
| Bass: |
Max bass boost/cut +/- 10 dB at 10 Hz
|
| Treble: |
Max treble boost/cut +/- 7.5 dB at 20 kHz
|
| Dimensions (H x W x D): |
115 x 430 x 385mm
(4.5 x 16.9 x 15.2”)
|
| Weight: |
15.0kg (33Lbs) |
Nuforce IA7 V2
- Power Output:
- 100W x 2 with 24,000uF of capacitance using 200W SMPS
- 325W peak power at 8 ohms.
- Power Bandwidth: 100 to 20 kHz +/- 0.8 db; 10 Hz -0.5 db; 60 kHz -3 db
- THD+N = 0.1%, 1kHz, 10W, 4 ohm load
- Remote input selection and volume control with memory (last selection, volume level)
- Digitally-controlled switched attenuator. Volume Range: +30dB to –70dB with 0.5dB steps
- Audio Inputs:
- 4 sets of RCA inputs (1 set can be configured as pre-out)
- Alternate configuration (available on black IA-7 only): 2 sets of RCA inputs, 1 3.5mm stereo input and 1 3.5 mm stereo pre-out
- Audio Outputs:
- 1 set of RCA preamp output jacks (only 3 sets of RCA inputs are available if this is configured)
- Speaker Binding Posts accept spade lugs or banana plugs
- Chassis is 100% high-grade, brushed and anodized aluminum to reduce audio resonance
- Dimensions: 1.75”H x 8.5”W x 16”D
- Weight: 8.5 lbs.
- Power Requirements: Worldwide 90-240VAC, auto select
Cary CAI 1
- Inputs: 1 pair XLR, 6 pair RCA
- Input Sensitivity: 1.2V (full-rated output)
- Record Output: 1 pair RCA
- Controller Connectors: Mini plug IR input, 3 Mini plugs for trigger out
- Communications: RS 232 Full remote configuration interface
- Volume Control Range: 63dB in 1dB steps
- Input Overload: 3V (single ended) / 6V (balanced)
- Input Impedance: 100K Ohms (single ended) / 200K Ohms (balanced)
- Output Impedance: 4Ω to 8Ω
- Frequency Response: 20Hz to 22kHz (±.5dB)
- Rated Power Output: 125wpc rms into 8Ω / 250wpc rms into 4Ω
- THD: 0.0005% 10W, 4 Ohms 14kHz / 15kHz
- THD+N: 0.006% @ 1W, 8Ω 1kHz, <0.2%, 0.1W - 200W, 4Ω
- Signal / Noise ratio: -80 dB CCIR
- Voltage Gain: 26.8 dB
- Damping Factor: > 4000, 100 Hz 8Ω
- Weight: 23 lbs
- Size: 4.5 x 17 x 13 (HxWxD in inches)
Naim NAIT 5i
Analogue inputs |
4 |
Input sensitivities |
225mV, 20kOhm |
Output level, tape |
225mV, 100 Ohm |
Power output (into 8 Ohms) |
50W per channel |
Overload margin, all inputs, all audio frequencies |
35dB |
Mains supply |
115V, 230V |
Dimensions (H x W x D) |
70 x 432 x 301mm |
Finish |
Black |
Audio Research VSI60
POWER OUTPUT: 50 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 1.5% at 50 watts, .05% at 1 watt.
FREQUENCY RESPONSE: (-3dB points at 1 watt)
1.0Hz to 80 kHz.
INPUT SENSITIVITY: 0.47V RMS Single-ended for rated output. (32.5dB gain into 8 ohms.)
INPUT IMPEDANCE: 50K ohms Single-ended.
INPUTS (5): CD, Tuner, Video, SE1, SE2 (Single Ended RCA connectors).
TUBES REQUIRED:
2 — Matched pair 6550. Power Output: 2-6H30 driver.
DIMENSIONS: 14" (35.6 cm) W x 8" (20.3 cm) H x 16"(40.6 cm) D. Rear connectors extend .88" beyond chassis.
WEIGHT: 34.8 lbs. (15.8 kg) Net; 38.3 lbs. (17.4 kg) Shipping.
Primare I21
Output Power: |
2 x 75 W into 8 Ohm
2 x 125 W into 4 Ohm
|
Speaker Terminals: |
4 - 16 Ohm |
Output Impedance: |
< 0.08 |
Line Inputs: |
330 mVrms |
Analogue Inputs: |
4 RCA (L & R) |
Preamp Output: |
1 RCA (L & R) |
Tape Outputs: |
300 mVrms |
Frequency Response: |
10 Hz - 100 kHz, -3 dB |
THD 0.05%: |
(1 kHz, 10 W into 8 Ohm) |
Signal-to-Noise Ration, Line: |
100 dB |
Power Consumption: |
Standby 12 W |
Peak Current: |
+/- 25 A |
Dimensions (WxDxH): |
430 x 385 x 100 mm |
Weight: |
13,5 kg |
Color Option: |
Black or titanium |
Primare I30
Output Power: |
2 x 100 W / 8 Ohm
2 x 180 W / 4 Ohm
|
Analogue Inputs: |
2 XLR (L & R)
4 RCA (L & R) |
Analogue Record Output: |
1 RCA (L & R) |
Pre Out: |
1 RCA (L & R) |
Peak Current: |
+/- 40 A |
Frequency Response: |
< 10 Hz - 100 kHz, -3 dB |
THD: |
< 0.07 % |
Signal-to-Noise Ratio, Line: |
100 dB |
Output Impedance: |
0.06 Ohm |
Power Consumption: |
Standby < 25 W |
Dimensions (WxDxH): |
430 x 385 x 100 mm |
Weight: |
15.5 kg |
Color Option: |
Black or Titanium |
Etalon Suprampli
Mains Voltage: 115, 125 or 230 V
Consumption: max. 120 VA
Inputs: High-level only
Sensitivity: min. 150 mV/10kOhm
Gain factor: 40 dB +/- 0,2 dB at 1 kHz
Output power: Min. 40 W at 4 Ohms
Output load: Not less than 2 Ohms
Weight: 8 kg
Dimensions: 300x115x385 mm, 12x5x15 inches
Etalon New Origo
Mains Voltage: 115, 125 or 230 V
Consumption: max. 120 VA
Inputs: High-level only
Sensitivity: min. 100 mV/10kOhm
Gain factor: 44 dB +/- 0,2 dB at 1 kHz
Output power: Min. 40 W at 4 Ohms
Output load: Not less than 2 Ohms
Weight: 16 kg
Dimensions: 460 x90x330 mm, 18x3½ x13 inches
MBL Basic 7006
- Input Sensitivity: 315mV
- Rated Power: 120W (8Ω), 185W (4Ω)
- Output current max: 20 A
- Input sensitivity: 1,5V, 185 W, 4Ω
- Frequency Response: DC – 135kHz / -3 dB
- Distortion THD+N: <0.006%, 4 Ω, 1 kHz, 50 W
- Damping Factor: 300 (4Ω)
MBL Noble 7008
- Input Sensitivity: 315mV
- Rated Power: 120W (8Ω), 200W (4Ω), 380W (2Ω)
- Output current max: 22 A
- Input sensitivity: 1,5V, 200 W, 4Ω
- Frequency Response: DC – 135kHz / -3 dB
- Distortion THD+N: <0.006%, 4 Ω, 1 kHz, 50 W
- Damping Factor: 300 (4Ω)
Consulte-nos para maiores detalhes sobre modelos e disponibilidade.
|